170190-01E 振动传感器 能够在很宽的频率范围内测量振动

基本细节:170190-01E 振动传感器 能够在很宽的频率范围内测量振动

170190-01E 是一款由Bently Nevada公司制造的振动传感器。这款传感器专为工业应用而设计，能够在很宽的频率范围内测量振动，使其能够检测到机械性能的微小变化。它的测量范围可以达到0-5mm/s，频率范围为10~1000Hz，工作温度范围为-20~80℃。此外，它的输出信号为4-20mA。
170190-01E振动传感器常用于石油和天然气、发电、化学处理以及制造业等行业。在这些领域中，它对于实时监测机械设备的工作状态，预防潜在故障以及优化设备性能起着关键作用。
170190-01E传感器的安装步骤通常涉及以下几个关键步骤。请注意，具体的安装步骤可能因设备型号、应用环境以及制造商的指南而有所不同，因此在实际安装前，务必参考制造商提供的产品手册和安装指南。
以下是170190-01E传感器安装的一般步骤：
准备工作：
确保安装环境符合传感器的操作要求，包括温度、湿度、振动等条件。
检查传感器和相关附件是否完整无损。
准备必要的安装工具，如螺丝刀、扳手等。
选择安装位置：
选择一个能够准确反映设备振动状态的位置，通常应靠近振动源。
确保安装位置平整、无油污、无腐蚀，且便于日后的维护和检查。
安装传感器底座：
根据传感器的尺寸和形状，在选定的位置上安装传感器底座。
使用合适的螺栓和螺母将底座固定牢固，确保底座与安装面之间的接触良好。
安装传感器：
将传感器放置在底座上，确保传感器的方向与振动方向一致。
使用制造商提供的安装工具，如锁紧环或锁紧螺丝，将传感器固定在底座上。
连接电缆：
根据制造商的指导，将传感器的输出电缆与数据采集系统或监测设备连接。
确保电缆连接牢固、无松动，并避免电缆受到过度的拉伸或弯曲。
测试与校准：
在安装完成后，对传感器进行测试，确保其工作正常并输出正确的振动信号。
如果需要，根据制造商的指南对传感器进行校准，以确保其测量结果的准确性。
完成安装：
检查所有安装步骤是否完成，确保没有遗漏或错误。
清理安装现场，确保工作区域整洁、安全。

170190-01E

The 170190-01E is a vibration sensor manufactured by Bently Nevada. Designed for industrial applications, this sensor is capable of measuring vibrations over a wide frequency range, enabling it to detect small changes in mechanical properties. Its measuring range can reach 0-5mm/s, the frequency range is 10~1000Hz, and the operating temperature range is -20~80℃. In addition, its output signal is 4-20mA.
The 170190-01E vibration sensor is commonly used in the oil and gas, power generation, chemical processing and manufacturing industries. In these fields, it plays a key role in real-time monitoring the working status of mechanical equipment, preventing potential failures, and optimizing equipment performance.
The 170190-01E sensor installation procedure usually involves the following key steps. Note that the installation procedure may vary depending on the device model, application environment, and the manufacturer’s guide. Therefore, ensure that you refer to the product manuals and installation guides provided by the manufacturer before the actual installation.
The following are the general steps for installing the 170190-01E sensor:
Preparation work:
Ensure that the installation environment meets the operating requirements of the sensor, such as temperature, humidity, and vibration.
Check that the sensor and related accessories are intact.
Prepare necessary installation tools, such as screwdrivers and wrenches.
Select the installation location:
Select a location that accurately reflects the vibration state of the device, usually close to the vibration source.
Ensure that the installation position is smooth, free of oil and corrosion, and convenient for future maintenance and inspection.
Install the sensor base:
Install the sensor base in the selected position according to the size and shape of the sensor.
Secure the base with proper bolts and nuts, and ensure that the base is in good contact with the mounting surface.
Install sensors:
Place the sensor on the base and ensure that the sensor is oriented in the same direction as the vibration.
Attach the sensor to the base using a mounting tool provided by the manufacturer, such as a locking ring or locking screw.
Connecting cable:
Connect the output cable of the sensor to the data acquisition system or monitoring device according to the manufacturer’s instructions.
Ensure that the cable connection is firm and not loose, and avoid excessive stretching or bending of the cable.
Test and calibration:
After the installation is complete, the sensor is tested to ensure that it is working properly and output the correct vibration signal.
If necessary, the sensor is calibrated according to the manufacturer’s guidelines to ensure the accuracy of its measurement results.
To complete the installation:
Check that all installation steps have been completed to ensure that there are no omissions or errors.
Clean up the installation site and ensure that the work area is clean and safe.

如果您需要查询或购买，请将产品型号发送到我的电子邮件或直接致电我

销售经理:何经理

手机: + 86 18005021035

邮箱: 18005021035@163.com

▲更多相关型号:170190-01E 振动传感器 能够在很宽的频率范围内测量振动